1 00:00:00,700 --> 00:00:08,500 In our next practice lab we'll take a look to the entire will and routing configuration. 2 00:00:08,650 --> 00:00:22,990 We are once rich and three lands created on that switch and we have tested at zero for 5 and 6 are connected 3 00:00:23,110 --> 00:00:28,100 to P.S. 1 3 ms 1 2 and 3. 4 00:00:28,360 --> 00:00:40,610 And our first returns 0 1 port of the Civic is connected to the rorters geek 0 0 interface. 5 00:00:40,970 --> 00:00:52,930 So first configure so each Port Vila hands and proper port modes so I understand that villains are not 6 00:00:52,930 --> 00:01:05,570 created so needs to be create I think we'll take a look to try to paint Pasi 2 from P.S. 1 then configure 7 00:01:05,730 --> 00:01:11,700 daughter's geek 0 1 sub interfaces with proper I pair this. 8 00:01:11,700 --> 00:01:14,580 I think this is wrong with them. 9 00:01:14,700 --> 00:01:17,180 This is gonna be gig. 10 00:01:17,190 --> 00:01:21,870 0 0 cousin in the figure is 0 0. 11 00:01:24,690 --> 00:01:27,850 And configure rather otherwise stick and in the first step. 12 00:01:27,840 --> 00:01:33,770 Try the pink piece it too from P.S. 1 again and let's go first. 13 00:01:33,820 --> 00:01:37,250 I'm going to make the configuration of the switch. 14 00:01:37,260 --> 00:01:41,000 I will create realism 15 00:01:44,870 --> 00:02:00,460 tend to end in 30 and I'm going to attach fest 0 4 to 10 0 5 to 20 in 0 6 to 30 and these guys will 16 00:02:00,460 --> 00:02:03,490 be switch port mode access 17 00:02:06,760 --> 00:02:08,500 and I'm going to make the 18 00:02:11,310 --> 00:02:17,280 first 01 to transport. 19 00:02:17,490 --> 00:02:18,090 Let's go 20 00:02:27,210 --> 00:02:27,780 woops 21 00:02:31,110 --> 00:02:34,900 let's make it some bigger that's better I think 22 00:02:37,620 --> 00:02:49,410 and let's create my v lines first in a row and config to create the airlines I'm using we land and will 23 00:02:49,410 --> 00:02:51,510 a number that I want to create. 24 00:02:51,520 --> 00:03:08,880 Command will 10 and their OK exit and I want to take a look if there is a will on configured on the 25 00:03:09,600 --> 00:03:10,560 switch first. 26 00:03:13,070 --> 00:03:20,080 As you can see the we just have default villain and we land terror right now. 27 00:03:20,160 --> 00:03:22,700 That means we need to create to an end. 28 00:03:22,780 --> 00:03:34,400 3 2 we land to any and we land 30 pretty straightforward and pretty cool. 29 00:03:34,400 --> 00:03:36,280 There is no problem in here. 30 00:03:37,440 --> 00:03:47,160 Now I need to attach my ports to that Wilkins interface first if there is 0 4 31 00:03:49,830 --> 00:03:59,530 will be a access port because I'm gonna use this port with one bill and only and this port 32 00:04:02,340 --> 00:04:05,760 will access to relent 10 33 00:04:09,190 --> 00:04:18,940 okay in the face first Internet 0 5 will be an access port again 34 00:04:23,820 --> 00:04:26,070 and we are gonna access to the real to any 35 00:04:31,460 --> 00:04:32,060 good 36 00:04:35,020 --> 00:04:39,520 and my sixth port will be an access port again 37 00:04:42,860 --> 00:04:53,300 and I'm going to access to William 30 whoa pretty cool. 38 00:04:53,300 --> 00:05:00,000 Now we need to configure the right port to also. 39 00:05:00,100 --> 00:05:03,230 This is precedents at one 40 00:05:10,510 --> 00:05:18,100 I'm making here wrong using these with port mode to run comment. 41 00:05:18,150 --> 00:05:18,930 All right. 42 00:05:19,180 --> 00:05:25,500 I think we accomplished the first step but I need to double check it configure switch port millions 43 00:05:25,500 --> 00:05:29,110 and port proper port modes. 44 00:05:29,430 --> 00:05:30,140 All right. 45 00:05:30,280 --> 00:05:42,180 I made my 0 1 as a talk and I created these real lines and attached these ports as access ports to this 46 00:05:42,180 --> 00:05:42,800 valence. 47 00:05:44,340 --> 00:05:45,270 OK. 48 00:05:46,710 --> 00:05:57,550 And now paying P.S. 2 from P.S. 1. 49 00:05:57,780 --> 00:06:16,930 I'm gonna go to P.S. 1 amping fitted up 3. 50 00:06:17,020 --> 00:06:21,860 Is there a line for Nat lemme see. 51 00:06:21,860 --> 00:06:26,340 Request timeout request timeout 52 00:06:33,370 --> 00:06:33,800 OK. 53 00:06:33,820 --> 00:06:39,670 As you can see that we cannot ping P.S. 2 from P.S. 1 right now. 54 00:06:44,360 --> 00:06:46,520 Here is the bad nose. 55 00:06:48,260 --> 00:06:53,420 Well I don't think so because we know how to communicate different villains. 56 00:06:56,250 --> 00:07:00,330 We just need a layer 3 device in this scenario. 57 00:07:00,340 --> 00:07:06,040 This is rather a and I hate to create sub interfaces 58 00:07:09,040 --> 00:07:15,940 and use get the addresses of these devices for my each sub interface. 59 00:07:17,860 --> 00:07:21,150 So I'm going to create a sorry. 60 00:07:21,220 --> 00:07:22,420 I'm going to assign 61 00:07:29,080 --> 00:07:42,620 these sub interface the IP address of the gateway of P.C. I'm this sub interface should have an IP address 62 00:07:42,620 --> 00:07:54,030 of 51 and this sub interface should have an IP address of sixty one 63 00:07:56,880 --> 00:08:04,680 and please don't forget that we need to take that sub interfaces because of we are gonna make real and 64 00:08:04,680 --> 00:08:06,800 communication over them 65 00:08:13,190 --> 00:08:14,090 all right. 66 00:08:14,300 --> 00:08:24,720 Let's go into the rather and CLIA. 67 00:08:24,900 --> 00:08:36,020 I'm gonna go to these sub interface mode interface key 0 0 that come first 68 00:08:39,570 --> 00:08:52,790 I'm going to use these as the gateway of the wheel and 10 so my IP address but first I need to take 69 00:08:52,790 --> 00:09:02,660 this with Vaillant 10 please remember it then I'm going to use the IP address of 41 70 00:09:14,500 --> 00:09:16,270 all right. 71 00:09:16,440 --> 00:09:17,050 Go 72 00:09:21,650 --> 00:09:25,280 51 and 61 will be the other sub interfaces 73 00:09:29,560 --> 00:09:31,750 so I will go to the interface. 74 00:09:31,750 --> 00:09:32,380 Geek 75 00:09:36,100 --> 00:09:41,710 zero slice zero up to any and IPA. 76 00:09:41,720 --> 00:09:56,340 This will be 50 but we need to first define the encapsulation as you can see in the morning to Oh no 77 00:09:59,210 --> 00:10:01,790 I clicked the wrong button. 78 00:10:03,790 --> 00:10:12,330 It also whereas it no. 79 00:10:12,520 --> 00:10:16,530 This is gonna be 20 surely. 80 00:10:16,640 --> 00:10:18,680 And my my IP address will be 81 00:10:21,200 --> 00:10:21,970 60 82 00:10:24,360 --> 00:10:30,090 Okay and let's go to the left sub interface 83 00:10:32,770 --> 00:10:38,740 encapsulation that one to 30 and we'll have an IP address of 84 00:10:43,420 --> 00:10:48,930 I think I configured the wrong IP address. 85 00:10:49,980 --> 00:10:55,000 Okay this is gonna be overlap. 86 00:10:55,400 --> 00:11:11,440 What I did is I forget to type 50 for the uh 2 anyway then and I'm gonna roll back down interface kick 87 00:11:16,430 --> 00:11:23,770 no IP address and we'll have an IP address or 50. 88 00:11:24,010 --> 00:11:25,720 This is gonna be 15 here 89 00:11:29,590 --> 00:11:36,050 and afters I will go to the 90 00:11:39,020 --> 00:11:51,680 last interface and I'm going to assign my IP address but first I then remember if I used encapsulation 91 00:11:54,820 --> 00:11:56,920 and I'm assigning my IP address now 92 00:12:01,140 --> 00:12:01,500 okay. 93 00:12:01,510 --> 00:12:11,840 Well your configuration you can make some mistakes and you need to quickly fix these mistakes guys. 94 00:12:11,840 --> 00:12:12,670 Okay. 95 00:12:12,680 --> 00:12:15,500 I completed my configuration right now. 96 00:12:15,590 --> 00:12:17,980 There should be no problem. 97 00:12:18,090 --> 00:12:35,630 So step two is accomplished and I'm not trying to ping P.S. To from P.S. 1 again P.S. 1 I'm not a ping 98 00:12:42,570 --> 00:12:43,950 I'm gonna pinging 99 00:12:47,150 --> 00:12:53,010 this IP address again. 100 00:12:53,080 --> 00:12:55,320 Here is the good news. 101 00:12:55,450 --> 00:12:57,570 Here is what I want to see. 102 00:12:57,570 --> 00:13:00,150 Seriously. 103 00:13:00,320 --> 00:13:00,920 All right. 104 00:13:00,950 --> 00:13:10,210 As you can see that we weren't able to ping before configuring our layer 3 devices. 105 00:13:10,220 --> 00:13:15,260 We couldn't make a communication between different villains. 106 00:13:15,590 --> 00:13:26,060 But after making the related configurations my pain was successful and I was able to make communication 107 00:13:26,090 --> 00:13:31,660 between different devices between different worlds. 108 00:13:31,670 --> 00:13:38,330 All right guys we have accomplished our goals and there is nothing to do more about this scenario right 109 00:13:38,360 --> 00:13:39,030 now. 110 00:13:39,080 --> 00:13:40,730 And thanks for waiting. 111 00:13:40,730 --> 00:13:42,650 See on the next session.