In the section we're going to talk about the HSR Pier practicing on the picket voices.
We are three steps to accomplish in the first step.
We need to make the HSR Chesapeake configuration for rather 1 2 according to these IP addresses.
OK.
Second we need to assign a suitable Gateway pelvis to your to our P.S..
All right.
And third we need to make sure that the packets from the P.S. go by the following read out on this direction
I think OK.
So what I'm going to do.
Let's make a summary in here.
I'm going to attach the
tender to the
interfaces the internal interfaces of the brothers and then the three for this other one and then the
three will be on rather two.
OK.
And I need to assign a suitable get a IP address that's gonna be our HSR IP IP.
So the gateway will be
then the one for the P.C. OK.
And third we need to make sure that the packets from the PCI go by following the red arrow.
So when I'm making the HSR pick config on the rather one I need to use a high prior to early and we
need to make sure that if this guy is being the active for the H is happy.
Oh OK.
Let's go.
So what I'm going to do is first I'm going to assign the IP addresses or I'm going to check if they're
already configured or not.
So OK I'm a rather one show IP interface brief and I can see that no IP address is configure.
All right IP of I'm sorry.
Interface faster it 0 0 and this guy will have an IP address of
tend to
okay.
And let's go to the other two and assign this other IP address.
Turned up three
and no shut.
All right.
I assigned the IP addresses and let's assign the default gateway to the P.C. my piece is IP address
is I need to recheck it then the
ten.
One hundred.
Okay.
Ten that one will be the gateway as we talked.
Okay
so I assigned the IP addresses to the first at 0 0 interfaces at 2 3 and 100 okay I assigned the suitable
gate where I paid risk to my piece as well.
All right.
Then what I need to do is to configure the HSR IP on Rather's.
And make sure that rather one is the active rather.
Okay I'm going to the rather one
so I need to show you how to reconfigure it interface fast turn it 0 0.
And I'm gonna assign I'm gonna assign the standby IP
as 10 that one
what is going wrong.
Okay.
There is no subnet mask.
Alright then stand by one
will have a prize to Wally which is bigger than the default bully of 100.
So I can use 200 to make sure that rather one is the default.
But I have another rather one.
Okay then I'm removing this configuration.
No stand by
I'm a rather too.
As you can see.
Okay.
No stand by one IP and no stand by one priority.
Okay.
Show run and check fast internet 0 0.
Okay.
We are not going the other one.
I'm sorry for the delay.
We are in the interface module already and what I need to do is configuring the standby one IP first
then standby one priority will be bigger than 100.
And that's gonna be arbitrary.
I choose the 200.
Okay then let's
I'm sorry.
Down.
We need to confirm your the pre-emption as well.
It's arbitrary too but if you're remembering from our slides I'm offering you to configure the pre-emption
always for the active rather.
Okay let's go with the rudder to
interface fast internet.
0 0 will have on standby.
One IP with turned up one so I don't want to configure the pre-emption and I am not gonna configure
the prior to my leave for rather to because the default Molly is 100 and as I cover your brother one
with the pride volley of the 200 I'm expecting to see that rather one is the active and rather 2 is
the standby Okay so let's check it.
Show standby
okay.
As I see from the show SMB output the state of the other one is active for the HSR P and my ritual IP
address is 10 that one.
Which is okay so let's take a loop to show standby and rather 2 state is standby and we are sharing
the 10 that one IP address with the other 1 Oh okay guys that's what I'm really want to see and I accomplished
the 3 steps 2 and H SRP configuration has finished.