1
00:00:00,950 --> 00:00:04,460
In the section we're going to talk about the link aggregation.

2
00:00:04,480 --> 00:00:12,100
And let's go ahead with the link aggregation our real link creation is a method for combining multiple

3
00:00:12,100 --> 00:00:18,490
network connections in parallel in order to increase throughput beyond what a single connection could

4
00:00:18,490 --> 00:00:26,290
sustain and to provide redundancy in case of the length should fail and either channel is a form of

5
00:00:26,380 --> 00:00:28,310
the link aggregation.

6
00:00:28,360 --> 00:00:29,860
Please pay attention.

7
00:00:29,920 --> 00:00:37,920
If you want to create an entire channel for two endpoints interface types must be same on both sides.

8
00:00:37,920 --> 00:00:47,800
For example gigabit to gigabit or right as you can see in here we have four separate gigabit links connecting

9
00:00:47,920 --> 00:00:57,880
these two which to each other and by using the ether channel we are combining them two together and

10
00:00:58,120 --> 00:01:03,760
we are getting one for gigabit per second or channel link.

11
00:01:03,800 --> 00:01:10,310
Let's go ahead with the benefits of the link aggregation we have some significant benefits you for using

12
00:01:10,310 --> 00:01:19,280
Blinkx aggregation guys and first you can forgive or just the EP P or port channel interface instead

13
00:01:19,280 --> 00:01:25,080
of configuring forced separate lanes as you can see in here.

14
00:01:25,280 --> 00:01:35,510
Secondly etre channel is just one logical link as you can see in year as for is spanning 3 port of call.

15
00:01:35,510 --> 00:01:47,100
For example if gigs get 1 0 1 link is down STPI recalculation is not made again.

16
00:01:47,450 --> 00:01:51,540
Third we can make load balancing the separate links.

17
00:01:51,560 --> 00:01:59,470
And lastly we can provide higher bandwidth to up to 8 bit per second.

18
00:02:00,810 --> 00:02:09,550
We're using two main protocols while we are creating it or channel and they are AGP and the NAACP more

19
00:02:09,870 --> 00:02:18,240
PDP is a Cisco proprietary protocol which is used for into Channel and can be configured to operate

20
00:02:18,330 --> 00:02:28,500
in three different modes and they are also on and did this terrible auto mode refers to personal negotiation

21
00:02:28,500 --> 00:02:36,320
of the channel this horrible Moudry refers to active niggled negotiation of the channel and on refers

22
00:02:36,480 --> 00:02:44,640
that no protocols are used it eschews the other side has enabled the link aggregation.

23
00:02:44,700 --> 00:02:57,530
So what they dismiss lets say we are to switch connect to each other and if I want to create an Internet

24
00:02:57,530 --> 00:03:07,340
channel between these two guys by using the PDP protocol we are choosing the channel molls skies and

25
00:03:07,410 --> 00:03:18,780
if one using a check fraud as also owns which one to create an entire channel I need to choose this

26
00:03:18,780 --> 00:03:28,300
Super Bowl for this issue because if I am using Outlook and if I were to create an ether so I cannot

27
00:03:28,330 --> 00:03:36,050
use auto and aren't even using for example dissyllable on this site.

28
00:03:38,860 --> 00:03:42,560
I should is also or this or both.

29
00:03:43,520 --> 00:03:49,430
On is to creator Joe by using the page.

30
00:03:50,020 --> 00:03:59,140
Let's go to L.A. C.P. L.A. C.P. is the I believe specification which is used for creating it or channel

31
00:03:59,380 --> 00:04:10,010
and can be configured to operate in three different modes and they're on active and passive all mode

32
00:04:10,090 --> 00:04:10,650
actuator.

33
00:04:10,780 --> 00:04:19,320
Port is the channel member without the protocol active mode enables LIHEAP unconditionally underlaid

34
00:04:19,330 --> 00:04:29,040
to the interface and passive mode enables LCP only van and LCP DeWyze is the director.

35
00:04:29,260 --> 00:04:36,150
For example let's say that we have sewage water and sewage Trigon in here and we have for example a

36
00:04:36,150 --> 00:04:45,100
set of four separate links between each other and to create again and interchange between these two

37
00:04:45,100 --> 00:04:51,000
guys by using LIHEAP which is an industry standard for this time.

38
00:04:51,130 --> 00:05:02,130
If I'm choosing the channel mode all in here for example for switch to I should use on just you from

39
00:05:02,140 --> 00:05:05,070
using aktif on this site.

40
00:05:05,170 --> 00:05:15,970
I need to choose active or passive and if when choosing the passive I should use the active on the other

41
00:05:15,970 --> 00:05:16,750
end.

42
00:05:18,460 --> 00:05:25,470
So let's go with to link aggregation configuration to configure it into channel.

43
00:05:25,460 --> 00:05:33,330
Firstly we need to check if our shesays supports it or channel or not guys.

44
00:05:33,340 --> 00:05:44,740
Secondly we need to make sure that duplex months which maybe half the legs or full the next port speeds

45
00:05:45,220 --> 00:05:50,900
which can be gigabit internet or fast internet or something like that.

46
00:05:51,100 --> 00:06:02,810
And the relearns maybe we run 20 30 or whatever days should merge on ports at both sides.

47
00:06:02,860 --> 00:06:14,960
OK guys let's say that we have four separate ports on each to switch as you can see in year gig was

48
00:06:15,000 --> 00:06:24,350
0 1 and gig was 0 3 4 3 2 1 and 1 0 2 1 0 4 4 the switched to.

49
00:06:24,550 --> 00:06:25,130
Okay.

50
00:06:25,190 --> 00:06:36,360
If I'm using a gig port on this side I should not use fast internet for example zero on on here if I'm

51
00:06:36,380 --> 00:06:40,080
using the legs on this side.

52
00:06:40,130 --> 00:06:49,490
I can not use half the place on this side for example if this poor these past two wheeler and 20 this

53
00:06:49,580 --> 00:06:54,280
poor should not be attached to the land for that for example.

54
00:06:54,320 --> 00:06:54,680
OK.

55
00:06:54,680 --> 00:07:03,260
To create an entire channel duplex mode support speeds and the willen numbers should match.

56
00:07:03,260 --> 00:07:11,270
And also we need to choose the right channel model Zino the configuration is pretty straightforward

57
00:07:12,090 --> 00:07:16,580
to establish and it's a channel between two separate switch.

58
00:07:16,580 --> 00:07:23,870
What you're saying is let's take a look to the switch once configuration first and getting into the

59
00:07:23,990 --> 00:07:36,650
interface mode by typing interface range Fester's 0 1 and 2 which means I'm going to apply these commands

60
00:07:36,650 --> 00:07:40,380
for boards first and 0 1 and 2.

61
00:07:40,790 --> 00:07:43,870
Ok I'm configuring the switch port modes.

62
00:07:43,920 --> 00:07:51,780
And as a trunk trunk and trunk then I'm choosing to channel more.

63
00:07:51,780 --> 00:08:00,040
For example Channel group Charile group number and mod will be active for this age.

64
00:08:00,360 --> 00:08:01,460
Alright cool.

65
00:08:01,740 --> 00:08:13,330
And on the switch to AGM and doing the similar things into price range then switchboard more trunk but

66
00:08:13,390 --> 00:08:22,540
please pay attention that this time Chello group the group numbers are matching also and I'm using the

67
00:08:22,600 --> 00:08:25,360
passive for this site.

68
00:08:25,420 --> 00:08:27,570
OK let's go ahead in here.

69
00:08:28,800 --> 00:08:38,160
As you can see here if choosing the active I need to use active or passive to create the entire channel

70
00:08:38,430 --> 00:08:46,000
and I can not use the on ARCA I'm going back to my scenario.

71
00:08:46,260 --> 00:08:54,180
And because of this to create any two channel we are using aktif on this side and passive on the other

72
00:08:54,240 --> 00:08:58,760
and I should not use on for this.

73
00:08:59,170 --> 00:09:06,980
And two to fight into Channel configuration or command is show it to channel summary.

74
00:09:07,770 --> 00:09:16,040
And we're seeing that the ports and the groups and the port channel if it is in use or not and the port

75
00:09:16,040 --> 00:09:17,910
of call or something like that.

76
00:09:18,120 --> 00:09:28,020
OK let's go have all three still we're turning the show into channels summary comment cool and I'm seeing

77
00:09:28,020 --> 00:09:35,230
the bundled ports in the entire channel and they're faster than 0 1 and face the time 0 2.

78
00:09:35,250 --> 00:09:46,500
As you can see in your alright is pretty good and I'm seeing a p value in here.

79
00:09:46,550 --> 00:09:57,800
PM Is this ports are in port channel which is a good news then I'm seeing the portico type we can use

80
00:09:57,820 --> 00:10:09,240
PDP or LCP as you know and here we are using L.L.C. be our our pool says that and I'm seeing the port

81
00:10:09,240 --> 00:10:15,750
channel number which is pure wan and I'm seeing an ass.

82
00:10:16,350 --> 00:10:29,120
And you what they need asked me Is this channel is a lathe to be interchangeable and you means our entire

83
00:10:29,130 --> 00:10:33,630
channel is working fine in use.